View D201GLY_5692280.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

may 2007 order number: d88126-001us the intel ? desktop board D201GLY may contain design defects or errors know n as errata that may cause the product to deviate from publishe d specifications. current characterized errata are documented in the in tel desktop board D201GLY specification update. intel? desktop board D201GLY technical product specification
revision history revision revision history date -001 first release of the intel? desktop board D201GLY technical product specification may 2007 this product specification applies to only standard intel desktop board D201GLY with bios identifier ly66210m.86a. changes to this specification will be pub lished in the intel desktop board D201GLY specification update before being incorporated into a revision of this document. information in this document is pr ovided in connection with intel ? products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. exce pt as provided in intel?s term s and conditions of sale for such products, intel assumes no liability what soever, and intel disclaims any express or implied warranty, relating to sale and/or us e of intel products in cluding liability or warranties relating to fitness for a particul ar purpose, merchantabi lity, or infringement of any patent, copyright or other intellectu al property right. in tel products are not intended for use in medical, life saving , or life sustaining applications. intel corporation may have patents or pending pate nt applications, trademar ks, copyrights, or other intellectual property rights that relate to the pres ented subject matter. the furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. intel may make changes to specifications and pr oduct descriptions at any time, without notice. designers must not rely on the absence or characteristi cs of any features or instru ctions marked ?reserved? or ?undefined.? intel reserves these for future defini tion and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. intel ? desktop boards may contain design defects or errors known as errata, which may cause the product to deviate from published specifications. current characterized errata are available on request. contact your local intel sales office or your distributor to obtain the latest specifications before placing your product order. copies of documents which have an ordering number and are referenced in this document, or other intel literature, may be obtained from: intel corporation p.o. box 5937 denver, co 80217-9808 or call in north america 1-800-548-4725, europe 44-0-1793-431-155, france 44-0-1793-421-777, germany 44-0-1793-421-333, other countries 708-296-9333. intel, the intel logo and celeron are registered trademarks of intel corporation or its subsidiaries in the united states and other countries. * other names and brands may be cl aimed as the property of others. copyright ? 2007, intel corporation. all rights reserved.
iii preface this technical product specification (tps) specifies the board layout, components, connectors, power and environmental requ irements, and the bios for the intel ? desktop board D201GLY. it describes the standard product and available manufacturing options. intended audience the tps is intended to provide detailed, technical information about the desktop board D201GLY and its components to the vendors, system integrators, and other engineers and technicians who need this level of information. it is specifically not intended for general audiences. what this document contains chapter description 1 a description of the hardware us ed on the desktop board D201GLY 2 a map of the resources of the desktop board 3 the features supported by the bios setup program 4 a description of the bios error messages and post codes typographical conventions this section contains information about the conventions used in this specification. not all of these symbols and abbreviations appear in all specifications of this type. notes, cautions, and warnings note notes call attention to important information. # integrator?s notes integrator?s notes are used to call attentio n to information that may be useful to system integrators. caution cautions are included to help you avoi d damaging hardware or losing data. warning warnings indicate conditions, which if not observed, can cause personal injury.
intel desktop board D201GLY te chnical product specification iv other common notation # used after a signal name to identify an active-low signal (such as usbp0#) (nxnx) when used in the description of a component, n indicates component type, xn are the relative coordinates of its location on the board, and x is the instance of the particular part at that general location. for example, j5j1 is a connector, located at 5j. it is the first connector in the 5j area. gb gigabyte (1,073,741,824 bytes) gb/sec gigabytes per second kb kilobyte (1024 bytes) kbit kilobit (1024 bits) kbits/sec 1000 bits per second mb megabyte (1,048,576 bytes) mb/sec megabytes per second mbit megabit (1,048,576 bits) mbit/sec megabits per second xxh an address or data value ending with a lowercase h indicates a hexadecimal value. x.x v volts. voltages are dc unless otherwise specified. * this symbol is used to indicate third-party brands and names that are the property of their respective owners.
v contents 1 product description 1.1 overview........................................................................................ 10 1.1.1 feature summary ................................................................ 10 1.1.2 manufacturing options .......................................................... 11 1.1.3 board layout ....................................................................... 12 1.1.4 block diagram ..................................................................... 14 1.2 online support................................................................................ 15 1.3 processor ....................................................................................... 15 1.4 system memory .............................................................................. 16 1.5 silicon integrated systems* chipset .................................................. 17 1.5.1 graphics subsystem ............................................................. 17 1.5.2 usb ................................................................................... 17 1.5.3 ide support ........................................................................ 18 1.5.4 real-time clock, cmos sram, and battery .............................. 19 1.6 s-video output ............................................................................... 23 1.7 legacy i/o controller ....................................................................... 23 1.7.1 serial port ........................................................................... 23 1.7.2 parallel port......................................................................... 24 1.7.3 keyboard and mouse interface ............................................... 24 1.8 audio subsystem............................................................................. 24 1.8.1 audio subsystem software .................................................... 24 1.8.2 audio connectors ................................................................. 25 1.9 lan subsystem ............................................................................... 26 1.9.1 lan subsystem software....................................................... 26 1.10 hardware management subsystem .................................................... 27 1.10.1 fan monitoring ..................................................................... 27 1.11 power management ......................................................................... 27 1.11.1 acpi .................................................................................. 28 1.11.2 hardware support ................................................................ 30 2 technical reference 2.1 memory map................................................................................... 35 2.2 connectors and headers................................................................... 36 2.2.1 back panel connectors .......................................................... 37 2.2.2 component-side connectors and headers ................................ 38 2.2.3 front panel usb headers ....................................................... 43 2.3 jumper blocks................................................................................. 44 2.3.1 front panel audio header/jumper block................................... 44 2.3.2 bios setup configuration jumper block .................................. 45 2.4 mechanical considerations ........... ..................................................... 46 2.4.1 form factor......................................................................... 46
intel desktop board D201GLY te chnical product specification vi 2.5 electrical considerations ........... ........................................................ 47 2.5.1 dc loading.......................................................................... 47 2.5.2 add-in board considerations .. ................................................ 47 2.5.3 fan header current capability................................................ 48 2.5.4 power supply considerations ................................................. 48 2.6 thermal considerations .................................................................... 49 2.7 reliability ....................................................................................... 51 2.8 environmental ................................................................................ 51 2.9 regulatory compliance..................................................................... 52 2.9.1 safety standards.................................................................. 52 2.9.2 european union declaration of conformity statement ................ 53 2.9.3 product ecology statements................................................... 55 2.9.4 emc regulations .................................................................. 59 2.9.5 product certification markings (b oard level)............................. 61 3 overview of bios features 3.1 introduction ................................................................................... 63 3.2 bios flash memory organization .. ..................................................... 64 3.3 resource configuration ............ ........................................................ 64 3.3.1 pci autoconfiguration ........................................................... 64 3.3.2 pci ide support................................................................... 65 3.4 system management bios (smbios)................................................. 65 3.5 legacy usb support ........................................................................ 66 3.6 bios updates ................................................................................. 66 3.6.1 language support ................................................................ 67 3.6.2 custom splash screen .......................................................... 67 3.7 boot options................................................................................... 67 3.7.1 cd-rom boot ...................................................................... 67 3.7.2 network boot....................................................................... 67 3.7.3 booting without attached devices........................................... 67 3.7.4 changing the default boot device during post ........................ 68 3.8 adjusting boot speed....................................................................... 68 3.8.1 peripheral selection and conf iguration..................................... 68 3.8.2 bios boot optimizations ....... ................................................ 69 3.9 bios security features .................................................................... 70 4 error messages 4.1 bios front-panel power led codes.................................................... 71 4.2 bios error messages ....................................................................... 71 4.3 port 80h post codes ....................................................................... 72
contents vii figures 1. board components .......................................................................... 12 2. block diagram ................................................................................ 14 3. back panel audio connectors ............................................................ 25 4. lan connector led locations ............................................................ 26 5. location of the standby power indicator led ....................................... 33 6. back panel connectors ..................................................................... 37 7. component-side connectors and headers ........................................... 38 8. connection diagram for front panel header ........................................ 41 9. connection diagram for front panel usb headers ................................ 43 10. location of the jumper blocks ... ........................................................ 44 11. board dimensions ........................................................................... 46 12. localized high temperature zones..................................................... 50 tables 1. feature summary............................................................................ 10 2. manufacturing options ..................................................................... 11 3. board components shown in figure 1 ................................................ 13 4. supported memory configurations ... .................................................. 16 5. lan connector led states ................................................................ 26 6. effects of pressing the power swit ch .................................................. 28 7. power states and targeted system power........................................... 29 8. wake-up devices and events ............................................................ 30 9. system memory map ....................................................................... 35 10. back panel connectors shown in figure 6 ........................................... 37 11. component-side connectors and headers shown in figure 7 ................. 39 12. front panel audio header ................................................................. 39 13. chassis fan connector ..................................................................... 39 14. main power connector...................................................................... 40 15. atx12v power connector ................................................................. 40 16. front panel header .......................................................................... 41 17. states for a one-color power led ...................................................... 42 18. states for a two-color power led...................................................... 42 19. front panel audio header/jumper block.............................................. 45 20. bios setup configuration jumper settings.......................................... 45 21. dc loading characteristics .......... ..................................................... 47 22. fan header current capability........................................................... 48 23. mtbf values ................................................................................... 51 24. environmental specifications........ ..................................................... 51 25. safety standards............................................................................. 52 26. lead-free board markings ................................................................ 58 27. emc regulations ............................................................................. 59 28. product certification markings ...... ..................................................... 61 29. bios setup program menu bar.......................................................... 64 30. bios setup program function keys.................................................... 64 31. boot device menu options ................................................................ 68
intel desktop board D201GLY te chnical product specification viii 32. supervisor and user password functions............................................. 70 33. front-panel power led blink codes .................................................... 71 34. bios error messages ....................................................................... 71 35. port 80h post code ranges.............................................................. 72 36. port 80h post codes ....................................................................... 73 37. typical port 80h post sequence........................................................ 76
9 1 product description what this chapter contains 1.1 overview........................................................................................ 10 1.2 online support................................................................................ 15 1.3 processor ....................................................................................... 15 1.4 system memory .............................................................................. 16 1.5 silicon integrated systems* chipset .................................................. 17 1.6 s-video output ............................................................................... 23 1.7 legacy i/o controller ....................................................................... 23 1.8 audio subsystem............................................................................. 24 1.9 lan subsystem ............................................................................... 26 1.10 hardware management subsystem .................................................... 27 1.11 power management ......................................................................... 27
intel desktop board D201GLY te chnical product specification 10 1.1 overview 1.1.1 feature summary table 1 summarizes the major features of the board. table 1. feature summary form factor mini-itx, compatible with microatx (6.75 inches by 6.75 inches [171.45 millimeters by 171.45 millimeters]) processor support for the following: ? soldered-down intel ? celeron ? processor with a 533 mhz system bus memory ? one 240-pin ddr2 sdram dual inline memory module (dimm) socket ? support for ddr2 667 mhz, ddr2 533 mhz and ddr2 400 mhz dimms (ddr 667 mhz validated to run at 533 mhz only) ? support for up to 1 gb of system memory chipset ? sis* sis662 northbridge ? sis sis964l southbridge video integrated sis mirage * 1 graphic engine audio adi* ad1888 audio codec legacy i/o control winbond* w83627dhg-b based legacy i/o controller for hardware management, serial, parallel, and ps/2* ports peripheral interfaces ? six usb 2.0 ports ? one serial port ? one parallel port ? one parallel ata ide interface with udma 33, ata-66/100/133 support ? ps/2 keyboard and mouse ports ? one s-video output port (optional) lan support 10/100 mbits/sec lan subsystem using broadcom* lan adapter device bios intel ? bios resident in the 4-mbit spi flash device expansion capabilities ? one pci* conventional bus connector hardware monitor subsystem (controlled by winbond w83627dhg-b i/o controller) ? voltage sense to detect out of range power supply voltages ? thermal sense to detect out of range thermal values ? two fan connectors ? one fan sense input used to monitor fan activity ? fan speed control
product description 11 1.1.2 manufacturing options table 2 describes the manufacturing options. not every manufacturing option is available in all marketing channels. please contact your intel representative to determine which manufacturing options are available to you. table 2. manufacturing options s-video output support for s-video output. one s-video output port lo cated on the back panel. for information about refer to available configurations for the desktop board D201GLY section 1.2, page 15
intel desktop board D201GLY te chnical product specification 12 1.1.3 board layout figure 1 shows the location of the major components. figure 1. board components table 3 lists the compon ents identified in figure 1.
product description 13 table 3. board components shown in figure 1 item/callout from figure 1 description a pci conventional bus add-in card connector b front panel usb headers c front panel audio header d back panel connectors e chassis fan header f +12v power connector (atx12v) g main power connector h intel celeron processor i dimm channel a socket j sis662 northbridge k parallel ata ide connector l front panel i/o header m battery n sis964l southbridge o bios setup configuration jumper block
intel desktop board D201GLY te chnical product specification 14 1.1.4 block diagram figure 2 is a block diagram of the majo r functional areas of the board. figure 2. block diagram
product description 15 1.2 online support to find information about? visit this world wide web site: intel ? desktop board D201GLY under ?desktop board products? or ?desktop board support? http://www.intel.com/design/motherbd http://support.intel.com/support/motherboards/desktop available configurations for the desktop board D201GLY http://developer.intel.com/desig n/motherbd/ly/ly_available.htm processor data sheets http://www.intel.com/products/index.htm audio software and utilities http://www.intel.com/design/motherbd lan software and drivers http://www.intel.com/design/motherbd 1.3 processor the board is designed to support the intel celeron processor 200-series soldered down with a 533 mhz system bus. for information about? refer to: supported processors for the D201GLY board http://www.intel.com/go/findcpu # integrator?s note use only atx12v-compliant power supplies. for information about refer to power supply connectors section 2.2.2.1, page 40
intel desktop board D201GLY te chnical product specification 16 1.4 system memory the board has one 240-pin dimm socket and supports the following memory features: ? 1.8 v (only) ddr2 sdram dimms with gold-plated contacts ? unbuffered, single-sided or double-sided dimms with the following restriction: double-sided dimms with x16 organization are not supported. ? 1 gb maximum total system memory ? minimum total system memory: 128 mb ? non-ecc dimms ? serial presence detect ? ddr2 533 or ddr2 400 mhz sdram dimms note to be fully compliant with all applicable ddr sdram memory specifications, the board should be populated with dimms that support the serial presence detect (spd) data structure. this allows the bios to read the spd data and program the chipset to accurately configure memory settings for op timum performance. if non-spd memory is installed, the bios will attempt to co rrectly configure the memory settings, but performance and reliability may be impacted or the dimms may not function under the determined frequency. table 4 lists the supported dimm configurations. table 4. supported memory configurations dimm capacity configuration sdram density sdram organization front-side/back-side number of sdram devices 128 mb ss 256 mbit 16 m x 16/empty 4 256 mb ss 256 mbit 32 m x 8/empty 8 256 mb ss 512 mbit 32 m x 16/empty 4 512 mb ds 256 mbit 32 m x 8/32 m x 8 16 512 mb ss 512 mbit 64 m x 8/empty 8 512 mb ss 1 gbit 64 m x 16/empty 4 1024 mb ds 512 mbit 64 m x 8/64 m x 8 16 1024 mb ss 1 gbit 128 m x 8/empty 8 note: in the second column, ?ds? refers to double-s ided memory modules (containing two rows of sdram) and ?ss? refers to single-sided memory modules (containing one row of sdram).
product description 17 1.5 silicon integrated systems* chipset the silicon integrated systems chipset consists of the following devices: ? sis662 northbridge ? sis964l southbridge the sis662 northbridge is a centralized cont roller for the system bus and the memory bus. the sis662 northbridge also provides integrated graphics capabilities supporting 3d, 2d, and display capabilities. the sis964l southbridge is a centralized controller for the board?s i/o paths. for information about refer to the silicon integrated systems sis662 northbridge http://www.sis.com/ the silicon integrated systems sis964l southbridge http://www.sis.com/ resources used by the chipset chapter 2 1.5.1 graphics subsystem the board uses the integrated mirage 1 gr aphic engine in the sis662 northbridge. 1.5.2 usb the board supports up to six usb 2.0 ports, supports uhci and ehci, and uses uhci- and ehci-compatible drivers. the sis964l southbridge provides the usb controller for all ports. the port arrangement is as follows: ? two ports are implemented with dual stac ked back panel connectors adjacent to the audio connectors ? four ports are routed to two se parate front panel usb headers note computer systems that have an unshielde d cable attached to a usb port may not meet fcc class b requirements, even if no device is attached to the cable. use shielded cable that meets the requ irements for full-speed devices. for information about refer to the location of the usb connectors on the back panel figure 6, page 37 the location of the front panel usb connectors figure 7, page 38
intel desktop board D201GLY te chnical product specification 18 1.5.3 ide support the board provides one parallel ata ide connector that supports two devices. 1.5.3.1 parallel ata ide interface the D201GLY board has one bus-mastering pa rallel ata ide interface. the parallel ata ide interface supports the following modes: ? programmed i/o (pio): processor controls data transfer. ? 8237-style dma: dma offloads the processo r, supporting transfer rates of up to 16 mb/sec. ? ultra dma: dma protocol on ide bus su pporting host and target throttling and transfer rates of up to 33 mb/sec. ? ata-66: dma protocol on ide bus suppo rting host and target throttling and transfer rates of up to 66 mb/sec. ata-66 protocol is similar to ultra dma and is device driver compatible. ? ata-100: dma protocol on ide bus allo ws host and target throttling. the sis964l?s ata-100 logic can achieve read tran sfer rates up to 100 mb/sec and write transfer rates up to 88 mb/sec. note ata-66 and ata-100 are faster timings and require a specialized cable to reduce reflections, noise, and inductive coupling. the parallel ata ide interface also support s atapi devices (such as cd-rom drives) and ata devices using the transfer modes. for information about refer to the location of the parallel ata ide connector figure 7, page 38
product description 19 1.5.4 real-time clock, cmos sram, and battery a coin-cell battery (cr2032) powers the re al-time clock and cmos memory. when the computer is not plugged into a wall so cket, the battery has an estimated life of three years. when the computer is plu gged in, the standby current from the power supply extends the life of the battery. the clock is accurate to 13 minutes/year at 25 oc with 3.3 vsb applied. note if the battery and ac power fail, custom defa ults, if previously saved, will be loaded into cmos ram at power-on. when the voltage drops below a certain leve l, the bios setup program settings stored in cmos ram (for example, the date and time) might not be accurate. replace the battery with an equivalent one. figure 1 on page 12 shows the location of the battery. caution risk of explosion if the battery is replaced with an incorrect type. batteries should be recycled where possible. disposal of used batteries must be in accordance with local environmental regulations. precaution risque d'explosion si la pile usage est remp lace par une pile de type incorrect. les piles usages doivent tre recycles dans la mesure du possible. la mise au rebut des piles usages doit respecter les rglementa tions locales en vigueur en matire de protection de l'environnement. forholdsregel eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. batterier b?r om muligt genbruges. bortskaffels e af brugte batterier b?r foreg? i overensstemmelse med g?ldende milj?lovgivning. obs! det kan oppst? eksplosjonsfare hvis batteriet skiftes ut med feil type . brukte batterier b?r kastes i henhold til gjeldende milj?lovgivning. viktigt! risk f?r explosion om batteriet ers?tts med felaktig batterityp. batterier ska kasseras enligt de lokala milj ?v?rdsbest?mmelserna. varo r?j?hdysvaara, jos pariston tyyppi on v??r ?. paristot on kierr?tett?v?, jos se on mahdollista. k?ytetyt paristot on h?vi tett?v? paikallisten ymp?rist?m??r?ysten mukaisesti.
intel desktop board D201GLY te chnical product specification 20 vorsicht bei falschem einsetzen einer neuen batteri e besteht explosionsgefahr. die batterie darf nur durch denselben oder einen en tsprechenden, vom hersteller empfohlenen batterietyp ersetzt werden. entsorgen si e verbrauchte batterien den anweisungen des herstellers entsprechend. avvertimento esiste il pericolo di un esplos ione se la pila non viene so stituita in modo corretto. utilizzare solo pile uguali o di tipo equivalente a quelle co nsigliate dal produttore. per disfarsi delle pile usate, seguir e le istruzioni del produttore. precaucin existe peligro de explosin si la pila no se cambia de forma adecuada. utilice solamente pilas iguales o del mismo tipo qu e las recomendadas por el fabricante del equipo. para deshacerse de las pilas usad as, siga igualmente las instrucciones del fabricante. waarschuwing er bestaat ontploffingsgevaar als de batteri j wordt vervangen door een onjuist type batterij. batterijen moeten zoveel moge lijk worden gerecycled. houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving. aten??o haver risco de explos?o se a bateria for su bstituda por um tipo de bateria incorreto. as baterias devem ser recicladas nos locais apropriados. a elimina??o de baterias usadas deve ser feita de acordo com as regulamenta??es ambientais da regi?o. a ? ciaro?zna ?? ?? ?? ?? ??? ??????? ????? ???????? ????? ???? ?????? ?????? ????? ? ? ?????? ??? ???? ?? ?????????? ????? upozornn v p ? ? ? ? ? ????? ????? ?????? ?? ???? ? ????? ? ??? ????????? ? ? ??????? ?? ? ???? ? ?? ? ????????? ?? ?? ???? ?? ???? ????? ?? ????????????? ???? ?? ? ???? ????? ? ??? ?? ? ???|????????? ?????????
product description 21 vigyazat ha a telepet nem a megfelel ? ? ? ? awas risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. bateri sepatutnya dikitar semula ji ka boleh. pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan. ostrze ? enie istnieje niebezpiecze ? ? ? ? ? ? ? ? ? precau ? ie risc de explozie, dac ? ? ? ? ? ? ? ??????? ??????? ???? ??????? ? ??? ? ? ??? ???? ???? ? ???????? ????? ?????? ???? ???? ??? ????? ???? ??? ?????? upozornenie ak batriu vymente za nesp rvny typ, hroz nebezpe ? ? ? ? pozor zamenjava baterije z baterijo druga ? ? ? ? .
intel desktop board D201GLY te chnical product specification 22 uyari yanl ? ld ? nda patlama riski vard r. piller m?mk?n oldu ? ? lm ? na uygun olarak at lmal d r. o ? ?????? ???? ?????? ? ???? ?????? ??? ??? ? ????? ?????? ???? ? ????? ????? ??????? ???? ?? ? ?????? ???? ???? ? ??? ? ?????
product description 23 1.6 s-video output the D201GLY board supports s-video outp ut via 7 pin s-vide o connector using sis307dv supporting both 4 pin s- video and composite signal. for information about refer to the silicon integrated systems sis307dv http://www.sis.com/ 1.7 legacy i/o controller the winbond w83672dhg-b legacy i/o contro ller provides the following features: ? one serial port ? one parallel port with extended capabilities port (ecp) and enhanced parallel port (epp) support ? serial irq interface compatible with seri alized irq support for pci conventional bus systems ? ps/2-style mouse and keyboard interfaces ? intelligent power management, including a programmable wake-up event interface ? pci conventional bus po wer management support the bios setup program provides configuration options for the i/o controller. 1.7.1 serial port the serial port a connector is located on the back panel. the serial port supports data transfers at speeds up to 115.2 kbits/sec with bios support. for information about refer to the location of the serial port a connector figure 6, page 37
intel desktop board D201GLY te chnical product specification 24 1.7.2 parallel port the 25-pin d-sub parallel port connector is lo cated on the back panel. use the bios setup program to set the parallel port mode. for information about refer to the location of the parallel port connector figure 6, page 37 1.7.3 keyboard and mouse interface ps/2 keyboard and mouse connectors are located on the back panel. note the keyboard is supported in the bottom ps/2 connector and the mouse is supported in the top ps/2 connector. power to the computer should be turned off before a keyboard or mouse is connected or disconnected. for information about refer to the location of the keyboard and mouse connectors figure 6, page 37 1.8 audio subsystem the audio subsystem consists of the following devices: ? sis964l southbridge ? adi ad1888 audio codec the audio subsystem includes these features: ? signal-to-noise ratio 90 db ? supports wake events (driver dependent) ? mic in pre-amp that supports dynamic, condenser, and electret microphones the audio subsystem supports th e following audio interfaces: ? front panel audio header, including pins for: ? line out ? mic in ? back panel audio connectors: ? line in ? line out ? mic in 1.8.1 audio subsystem software audio software and drivers are availabl e from intel?s worl d wide web site. for information about refer to obtaining audio software and drivers section 1.1.4, page 14
product description 25 1.8.2 audio connectors the board contains audio connectors on the back panel and an audio header on the component side of the board. the front pane l audio header is a 2 x 5-pin header that provides mic in and line out signal s for front panel audio connectors. the audio subsystem connectors are shown in figure 3. item description a line in b line out c mic in figure 3. back panel audio connectors for information about refer to the location of the front panel audio header figure 7, page 38 the signal names of the front panel audio header table 12, page 39
intel desktop board D201GLY te chnical product specification 26 1.9 lan subsystem the lan subsystem consists of the following: ? broadcom ac131klmg lan adapter device for 10/100 mbits/sec ethernet lan connectivity ? rj-45 lan connector with integrated status leds ? programmable transit threshold ? configurable eeprom that contains the mac address two leds are built into the rj-45 lan connector (shown in figure 4). figure 4. lan connector led locations table 5 describes the led states when the board is powered up and the 10/100 mbits/sec lan subsystem is operating. table 5. lan connector led states led color led state condition off lan link is not established. on lan link is established. green blinking lan activity is occurring. off 10 mbits/sec data rate is selected. yellow on 100 mbits/sec data rate is selected. 1.9.1 lan subsystem software lan software and drivers are availabl e from intel?s worl d wide web site. for information about refer to obtaining lan software and drivers section 1.1.4, page 14
product description 27 1.10 hardware management subsystem the hardware management features enable th e board to be compatible with the wired for management (wfm) specification. the winbond w83627dhg-b i/o controller is used to implement hardware monitoring and fan control. the features of this i/o controller include: ? internal ambient temperature sensor ? two remote thermal diode sensors for dire ct monitoring of processor temperature and ambient temperature sensing ? power supply monitoring of four voltages (+5 v, +v_1p8__core, +vccp, and +12 v) to detect levels above or below acceptable values ? thermally monitored closed-loop fan control, for system fan, that can adjust the fan speed or switch the fans on or off as needed ? smbus interface 1.10.1 fan monitoring fan monitoring can be implemented using intel ? desktop utilities, landesk* software, or third-party software. for information about refer to the functions of the fan connectors section 1.11.2.2, page 31 1.11 power management power management is implemented at several levels, including: ? software support through advanced conf iguration and power interface (acpi) ? hardware support: ? power connector ? fan connectors ? lan wake capabilities ? instantly available pc technology ? resume on ring ? wake from usb ? wake from ps/2 devices ? power management event sign al (pme#) wake-up support
intel desktop board D201GLY te chnical product specification 28 1.11.1 acpi acpi gives the operating system direct co ntrol over the power management and plug and play functions of a computer. the us e of acpi with this board requires an operating system that provides full acpi support. acpi features include: ? plug and play (including bus and device enumeration) ? power management control of individual devices, add-in boards (some add-in boards may require an acpi-aware driver), video displays, and hard disk drives ? methods for achieving less than 15-watt syst em operation in the power-on/standby sleeping state ? a soft-off feature that enables the operat ing system to power-off the computer ? support for multiple wake-up events (see table 8 on page 30) ? support for a front panel power and sleep mode switch table 6 lists the system states based on how long the power switch is pressed, depending on how acpi is configured with an acpi-aware operating system. table 6. effects of pressing the power switch if the system is in this state? ?and the power switch is pressed for ?the system enters this state off (acpi g2/g5 ? soft off) less than four seconds power-on (acpi g0 ? working state) on (acpi g0 ? working state) less than four seconds soft-off/standby (acpi g1 ? sleeping state) on (acpi g0 ? working state) more than four seconds fail safe power-off (acpi g2/g5 ? soft off) sleep (acpi g1 ? sleeping state) less than four seconds wake-up (acpi g0 ? working state) sleep (acpi g1 ? sleeping state) more than four seconds power-off (acpi g2/g5 ? soft off)
product description 29 1.11.1.1 system states and power states under acpi, the operating system direct s all system and device power state transitions. the operating system puts de vices in and out of low-power states based on user preferences and knowledge of how devices are being used by applications. devices that are not being used can be tu rned off. the operating system uses information from applications and user setti ngs to put the system as a whole into a low-power state. table 7 lists the power states supported by the board along with the associated system power targets. see the acpi specif ication for a complete description of the various system and power states. table 7. power states and targeted system power global states sleeping states processor states device states targeted system power (note 1) g0 ? working state s0 ? working c0 ? working d0 ? working state. full power > 30 w g1 ? sleeping state s1 ? processor stopped c1 ? stop grant d1, d2, d3 ? device specification specific. 5 w < power < 52.5 w g1 ? sleeping state s4 ? suspend to disk. context saved to disk. no power d3 ? no power except for wake-up logic. power < 5 w (note 2) g2/s5 s5 ? soft off. context not saved. cold boot is required. no power d3 ? no power except for wake-up logic. power < 5 w (note 2) g3 ? mechanical off ac power is disconnected from the computer. no power to the system. no power d3 ? no power for wake-up logic, except when provided by battery or external source. no power to the system. service can be performed safely. notes: 1. total system power is dependent on the system co nfiguration, including add- in boards and peripherals powered by the system chassis? power supply. 2. dependent on the standby power consumptio n of wake-up devices used in the system.
intel desktop board D201GLY te chnical product specification 30 1.11.1.2 wake-up devices and events table 8 lists the devices or specific events that can wake the computer from specific states. table 8. wake-up devices and events these devices/events can wake up the computer? ?from this state lan s1, s4, s5 (note) modem (back panel serial port a) s1 pme# signal s1, s4, s5 (note) power switch s1, s4, s5 ps/2 devices s1 rtc alarm s1, s4, s5 usb s1 note: for lan and pme# signal, s5 is disabled by default in the bios setup program. setting this option to power on will enable a wake-up event from lan in the s5 state. note the use of these wake-up events from an acpi state requires an operating system that provides full acpi support. in additi on, software, drivers, and peripherals must fully support acpi wake events. 1.11.2 hardware support caution ensure that the power supply provides adeq uate +5 v standby current if lan wake capabilities and instantly available pc technolo gy features are used. failure to do so can damage the power supply. the total am ount of standby current required depends on the wake devices supported and manufacturing options. the board provides several power manage ment hardware features, including: ? power connector ? fan headers ? lan wake capabilities ? instantly available pc technology ? resume on ring ? wake from usb ? wake from ps/2 keyboard ? pme# signal wake-up support ? wake# signal wake-up support lan wake capabilities and instantly available pc technology require power from the +5 v standby line.
product description 31 resume on ring enables tele phony devices to access the computer when it is in a power-managed state. the method used de pends on the type of telephony device (external or internal). note the use of resume on ring and wake from usb technologies from an acpi state requires an operating system th at provides full acpi support. 1.11.2.1 power connector atx12v-compliant power supplies can turn off the system power through system control. when an acpi-enabled system receives the correct command, the power supply removes all non-standby voltages. when resuming from an ac power failure, th e computer returns to the power state it was in before power was interrupted (on or off). the computer?s response can be set using the last power state feature in th e bios setup program?s boot menu. for information about refer to the location of the main power connector figure 7, page 38 the signal names of the main power connector table 14, page 40 1.11.2.2 fan headers the function/operation of the fan headers is as follows: ? the fans are on when the boar d is in the s0 or s1 state. ? the fans are off when the board is off or in the s4 or s5 state. ? system fan header is wired to a fa n tachometer input of the winbond w83627dhg-b i/o controller. ? all fan headers have a +12 v dc connection. for information about refer to the signal names of the chassis fan headers table 13, page 39 1.11.2.3 lan wake capabilities caution for lan wake capabilities, the +5 v standby line for the power supply must be capable of providing adequate +5 v standby current . failure to provide adequate standby current when implementing lan wake capa bilities can damage the power supply. lan wake capabilities enable remote wake-up of the computer through a network. the lan network adapter monitors network tra ffic at the media independent interface. upon detecting a magic packet* frame, th e lan subsystem asserts a wake-up signal that powers up the computer. dependin g on the lan implementation, the board supports lan wake capabilities with acpi in the following ways: ? the pci conventional bus pme# signal for pci 2.2 compliant lan designs ? the onboard lan subsystem
intel desktop board D201GLY te chnical product specification 32 1.11.2.4 resume on ring the operation of resume on ring can be summarized as follows: ? resumes operation from acpi s1 states ? detects incoming call similarly fo r external and internal modems ? requires modem interrupt be unmasked for correct operation 1.11.2.5 wake from usb usb bus activity wakes the co mputer from acpi s1 states. note wake from usb requires the use of a usb peripheral that supports wake from usb. 1.11.2.6 wake from ps/2 devices ps/2 device activity wakes the co mputer from an acpi s1 state. 1.11.2.7 pme# signal wake-up support when the pme# signal on the pci conventi onal bus is asserted, the computer wakes from an acpi s1, s4, or s5 state (w ith wake on pme enabled in bios).
product description 33 1.11.2.8 +5 v standby power indicator led the +5 v standby power indicator led shows that power is still present even when the computer appears to be off. figure 5 shows the locati on of the standby power indicator led. caution if ac power has been switched off and the standby power indicator is still lit, disconnect the power cord befo re installing or removing an y devices connected to the board. failure to do so could damage the board an d any attached devices. figure 5. location of the standby power indicator led
intel desktop board D201GLY te chnical product specification 34
35 2 technical reference what this chapter contains 2.1 memory map................................................................................... 35 2.2 connectors and headers................................................................... 36 2.3 jumper blocks................................................................................. 44 2.4 mechanical considerations ........... ..................................................... 46 2.5 electrical considerations ........... ........................................................ 47 2.6 thermal considerations .................................................................... 49 2.7 reliability ....................................................................................... 51 2.8 environmental ................................................................................ 51 2.9 regulatory compliance..................................................................... 52 2.1 memory map table 9 lists the system memory map. table 9. system memory map address range (decimal) address range (hex) size description 1024 k - 1048576 k 100000 - ffffffff 4095 mb extended memory 960 k - 1024 k f0000 - fffff 64 kb runtime bios 896 k - 960 k e8000 - effff 32 kb reserved 800 k - 896 k c8000 ? e7fff 128 kb potential available high dos memory (open to the pci conventional bus). dependent on video adapter used. 640 k - 800 k a0000 - c7fff 160 kb video memory and bios 639 k - 640 k 9fc00 - 9ffff 1 kb extended bios data (movable by memory manager software) 512 k - 639 k 80000 - 9fbff 127 kb extended conventional memory 0 k - 512 k 00000 - 7ffff 512 kb conventional memory
intel desktop board D201GLY te chnical product specification 36 2.2 connectors and headers caution only the following connectors/ headers have overcurrent protection: back panel usb, front panel usb, and ps/2. the other internal connectors/headers ar e not overcurrent protected and should connect only to devices inside the computer ?s chassis, such as fans and internal peripherals. do not use these connectors/ headers to power devices external to the computer?s chassis. a fault in the load pr esented by the external devices could cause damage to the computer, the power cable, and the external devices themselves. this section describes the board?s conne ctors and headers. the connectors and headers can be divided into these groups: ? back panel i/o connectors (see page 37) ? component-side i/o connectors and headers (see page 38)
technical reference 37 2.2.1 back panel connectors figure 6 shows the location of the back pa nel connectors. the back panel connectors are color-coded. the figure legend ( table 10) lists the colors used (when applicable). figure 6. back panel connectors table 10. back panel connectors shown in figure 6 item/callout from figure 6 description a ps/2 mouse port (green) b ps/2 keyboard port (purple) c parallel port (burgundy) d serial port a (teal) e vga port f s-video output (optional) g lan h usb ports [2] i line in j mic in k line out note the back panel audio line out connector is de signed to power headphones or amplified speakers only. poor audio quality occurs if passive (non-amplified) speakers are connected to this output.
intel desktop board D201GLY te chnical product specification 38 2.2.2 component-side connectors and headers figure 7 shows the locations of the co mponent-side connectors and headers. figure 7. component-side connectors and headers table 11 lists the component-side co nnectors and headers identified in figure 7.
technical reference 39 table 11. component-side connectors and headers shown in figure 7 item/callout from figure 7 description a pci conventional bus add-in card connector b front panel usb header c front panel usb header d front panel audio header e chassis fan header f +12v power connector (atx12v) g main power connector h processor fan header i parallel ata ide connector j front panel header table 12. front panel audio header pin signal name pin signal name 1 mic 2 ground 3 mic bias 4 ground 5 fp_out_r 6 fp_return_r 7 +5 v 8 key 9 fp_out_l 10 fp_return_l # integrator?s note the front panel audio connector is alternatel y used as a jumper block for routing audio signals. refer to section 2.3 on page 44 for more information . table 13. chassis fan connector pin signal name 1 control 2 +12 v 3 tach
intel desktop board D201GLY te chnical product specification 40 2.2.2.1 power supply connectors the board has the following power supply connectors: ? main power ? a 2 x 10 connector. the board supports the use of atx12v power supplies with 2 x 10 or 2 x 12 main power cables. ? atx12v power ? a 2 x 2 connector. this connect or provides power directly to the processor voltage regulator and must always be used. failure to do so will prevent the board from booting. table 14. main power connector pin signal name pin signal name 1 +3.3 v 11 +3.3 v 2 +3.3 v 12 -12 v 3 ground 13 ground 4 +5 v 14 ps-on# (power supply remote on/off) 5 ground 15 ground 6 +5 v 16 ground 7 ground 17 ground 8 pwrgd (power good) 18 +5 v 9 +5 v (standby) 19 +5 v 10 +12 v 20 +5 v table 15. atx12v power connector pin signal name pin signal name 1 ground 2 ground 3 +12 v 4 +12 v 2.2.2.2 add-in card connectors the board has one pci conventional (rev 2. 3 compliant) bus add-in card connector. pci conventional bus add-in cards with smbus support can access sensor data and other information residing on the board. note the following considerations fo r the pci conventional bus connector: ? the pci conventional bus connect or is bus master capable. ? smbus signals are routed to the pci conven tional bus connector. this enables pci conventional bus add-in boards with smbu s support to access sensor data on the board. the specific smbus signals are as follows: ? the smbus clock line is connected to pin a40. ? the smbus data line is connected to pin a41.
technical reference 41 2.2.2.3 front panel header this section describes the functi ons of the front panel header. table 16 lists the signal names of the front panel header. figure 8 is a connection diagram for the front panel header. table 16. front panel header pin signal in/out description pin signal in/out description hard drive activity led [orange] power led [green] 1 hd_pwr out hard disk led pull-up to +5 v 2 hdr_blnk_ grn out front panel green led 3 had# out hard disk active led 4 hdr_blnk_ yel out front panel yellow led reset switch [blue] on/off switch [red] 5 ground ground 6 fpbut_in in power switch 7 fp_reset# in reset switch 8 ground ground power not connected 9 +5 v power 10 n/c not connected figure 8. connection diagram for front panel header
intel desktop board D201GLY te chnical product specification 42 2.2.2.3.1 hard drive activity led header [orange] pins 1 and 3 [orange] can be connected to an led to provide a visual indicator that data is being read from or written to a hard drive. proper led function requires an ide hard drive connected to an onboard ide connector. 2.2.2.3.2 reset switch header [blue] pins 5 and 7 [blue] can be connected to a momentary single pole, single throw (spst) type switch that is normally open. when the switch is closed, the board resets and runs the post. 2.2.2.3.3 power/sleep led header [green] pins 2 and 4 [green] can be connected to a one- or two-color led. table 17 shows the possible states for a one-color led. table 18 shows the possible states for a two- color led. table 17. states for a one-color power led led state description off power off/sleeping steady green running table 18. states for a two-color power led led state description off power off steady green running steady yellow sleeping note the colors listed in table 17 and table 18 are suggested colors only. actual led colors are product- or customer-specific. 2.2.2.3.4 power switch header [red] pins 6 and 8 [red] can be connected to a front panel momentary-contact power switch. the switch mu st pull the sw_on# pin to ground for at least 50 ms to signal the power supply to switch on or off. (t he time requirement is due to internal debounce circuitry on the board.) at leas t two seconds must pass before the power supply will recognize another on/off signal.
technical reference 43 2.2.3 front panel usb headers figure 9 is a connection diagram for the front panel usb headers. # integrator?s notes x the +5 v dc power on the usb connector is fused. x pins 1, 3, 5, and 7 comprise one usb port. x pins 2, 4, 6, and 8 comprise one usb port. x use only a front panel usb connector that conforms to the usb 2.0 specification for high-speed usb devices. figure 9. connection diagram for front panel usb headers
intel desktop board D201GLY te chnical product specification 44 2.3 jumper blocks caution do not move any jumpers with the power on . always turn off the power and unplug the power cord from the computer before ch anging a jumper setting. otherwise, the desktop board could be damaged. figure 10 shows the location of the jumper blocks. item description a front panel audio header/jumper block b bios setup configuration jumper block figure 10. location of the jumper blocks 2.3.1 front panel audio header/jumper block this connector has two functions: ? with jumpers installed, the audio line out an d mic in signals are routed to the back panel audio connectors. ? with jumpers removed, the connector provid es audio line out and mic in signals for front panel audio headers. table 19 describes the two configurations of this header/jumper block.
technical reference 45 caution do not place jumpers on this block in any configuration other than the one described in table 19. other jumper configurations are not supported and could damage the desktop board. table 19. front panel audio header/jumper block jumper setting configuration 5 and 6 9 and 10 audio line out and mic in signals ar e routed to the back panel audio connectors. the back panel audio connectors are shown in figure 6 on page 37. no jumpers installed table 12 on page 39 lists the names of the signals available on this connector when no jumpers are installed. # integrator?s note when the jumpers are removed and this conne ctor is used for front panel audio, the back panel audio line out and mic in connectors are disabled. 2.3.2 bios setup configuration jumper block this 3-pin jumper block determines the bios setup program?s mode. table 20 describes the jumper settings for the three mo des: normal, config ure, and recovery. when the jumper is set to configuration mode and the computer is powered-up, the bios compares the processor version and the microcode version in the bios and reports if the two match. table 20. bios setup configuration jumper settings function/mode jumper setting configuration normal 1-2 321 the bios uses current configuration information and passwords for booting. configure 2-3 321 after the post runs, setup runs automatically. the maintenance menu is displayed. recovery none 321 the bios attempts to recover the bios configuration. a recovery diskette is required.
intel desktop board D201GLY te chnical product specification 46 2.4 mechanical considerations 2.4.1 form factor the board is designed to fit into a microatx-form-factor chassis. figure 11 illustrates the mechanical form factor of the board. dimensions are given in inches [millimeters]. the outer dimensions are 6.75 inches by 6.75 inches [171.45 millimeters by 171.45 millimeters]. location of the i/o connectors and mounting holes are in compliance with the micro-atx specification. figure 11. board dimensions
technical reference 47 2.5 electrical considerations 2.5.1 dc loading table 21 lists the dc loading characteristics of the board. this data is based on a dc analysis of all active components within the board that impact its power delivery subsystems. the analysis does not include pci add-in cards. minimum values assume a light load placed on the board that is sim ilar to an environment with no applications running and no usb current draw. maximum values assume a load placed on the board that is similar to a heavy gaming environment with a 500 ma current draw per usb port. these calculations are not based on specific processor values or memory configurations but are based on the mi nimum and maximum cu rrent draw possible from the board?s power delivery subsyste ms to the processor, memory, and usb ports. use the datasheets for add-in cards, such as pci, to determine the overall system power requirements. the selection of a powe r supply at the system level is dependent on the system?s usage model and not necessar ily tied to a particular processor speed. table 21. dc loading characteristics dc current at: mode dc power +3.3 v +5 v +12 v -12 v +5 vsb minimum loading 45 w 2.0 a 1.8 a 2.19 a 0 a 0.25 a maximum loading 175 w 4.42 a 17.88 a 5.15 a 0.1 a 1.19 a 2.5.2 add-in board considerations the board is designed to provide 2 a (average ) of +5 v current for one add-in board.
intel desktop board D201GLY te chnical product specification 48 2.5.3 fan header current capability caution the processor fan must be connected to the processor fan header, not to a chassis fan header. connecting the processor fan to a chassis fan header may result in onboard component damage that will halt fan operation. table 22 lists the current capability of the fan headers. table 22. fan header current capability fan header maximum available current processor fan 2 a rear chassis fan 1.5 a 2.5.4 power supply considerations caution the +5 v standby line for the power supply must be capable of providing adequate +5 v standby current. failure to do so can damage the power supply. the total amount of standby current required depe nds on the wake devices supported and manufacturing options. system integrators should refer to the power usage values listed in table 21 when selecting a power supply for use with the board. additional power required will depend on configurations chosen by the integrator. the power supply must comply with the following recommendations found in the indicated sections of the atx form factor specification. ? the potential relation between 3.3 vdc and +5 vdc power rails ? the current capability of the +5 vsb line ? all timing parameters ? all voltage tolerances
technical reference 49 2.6 thermal considerations caution failure to ensure appropriate airflow may re sult in reduced performance of both the processor and/or voltage regulator or, in some instances, damage to the board. for a list of chassis that have been tested with intel desktop boards please refer to the following website: http://developer.intel.com/design/motherbd/cooling.htm all responsibility for determining the adeq uacy of any thermal or system design remains solely with the reader. intel ma kes no warranties or representations that merely following the instructions presented in this document will result in a system with adequate thermal performance. caution ensure that the ambient temperature does not exceed the board?s maximum operating temperature. failure to do so could cause components to exceed their maximum case temperature and malfunction. for info rmation about the maximum operating temperature, see the environmental specifications in section 2.8. caution ensure that proper airflow is maintained in the processor voltage regulator circuit. failure to do so may result in damage to the voltage regu lator circuit. the processor voltage regulator area (item a in figure 12) can reach a temperature of up to 85 o c in an open chassis.
intel desktop board D201GLY te chnical product specification 50 figure 12 shows the locations of the localized high temperature zones. item description a processor voltage regulator area b processor c sis662 northbridge d sis964l southbridge figure 12. localized high temperature zones the operating temperature, current load, or operating frequency could affect case temperatures. maximum case temperatures are important when considering proper airflow to cool the board. for processor case temperature, see processor datasheets and processor specification updates for su pported processors. for chipset thermal information, refer to the following website: http:\www.sis.com
technical reference 51 2.7 reliability the mean time between failures (mtbf) pred iction is calculated using component and subassembly random failure rates. the calculation is based on the bellcore reliability prediction procedure, tr-nwt-000332, issue 4, september 1991. the mtbf prediction is used to estimate repa ir rates and spare parts requirements. the mtbf data is calculated from predicted data at 55 oc. table 23 shows the mtbf value for each of the D201GLY bo ard?s manufacturing options: table 23. mtbf values product code mtbf value laD201GLYt 327175.8832 hours laD201GLY 327175.8832 hours box/blkD201GLYl 339835.5196 hours laD201GLYt1 327175.8832 hours laD201GLYl1 327175.8832 hours box/blkD201GLYl1 339835.5196 hours 2.8 environmental table 24 lists the environmental specifications for the board. table 24. environmental specifications parameter specification temperature non-operating -40 c to +70 c operating 0 c to +55 c shock unpackaged 50 g trapezoidal waveform velocity change of 170 inches/second packaged half sine 2 millisecond product weight (pounds) free fall (inches) velocity change (inches/sec 2 ) <20 36 167 21-40 30 152 41-80 24 136 81-100 18 118 vibration unpackaged 5 hz to 20 hz: 0.01 g2 hz sloping up to 0.02 g2 hz 20 hz to 500 hz: 0.02 g2 hz (flat) packaged 5 hz to 40 hz: 0.015 g2 hz (flat) 40 hz to 500 hz: 0.015 g2 hz sloping down to 0.00015 g2 hz
intel desktop board D201GLY te chnical product specification 52 2.9 regulatory compliance this section contains the following regulatory compliance information for desktop board D201GLY: ? safety standards ? european union declaration of conformity statement ? product ecology statements ? electromagnetic compatibility (emc) standards ? product certification markings 2.9.1 safety standards desktop board D201GLY complies with the safety standards stated in table 25 when correctly installed in a compatible host system. table 25. safety standards standard title ul 60950-1, first edition information technology equipment ? safety - part 1: general requirements (usa and canada) en 60950-1:2006, second edition information technology equipmen t ? safety - part 1: general requirements (european union) iec 60950-1:2005, second edition information technology equipmen t ? safety - part 1: general requirements (international)
technical reference 53 2.9.2 european union declaration of conformity statement we, intel corporation, declare under our sole responsibility that the product intel ? desktop board D201GLY is in conformity wi th all applicable essential requirements necessary for ce marking, following the provisions of the european council directive 2004/108/ec(emc directive) and 2006/95/ ec (low voltage directive). the product is properly ce marked demo nstrating this conformity and is for distribution within all member states of the eu with no restrictions. this product follows the provisions of the european directives 2004/108/ec and 2006/95/ec. ? e?tina tento vyrobek odpovd po?adavk ? m evropskych sm rnic 2004/108/ec a 2006/95/ec. dansk dette produkt er i overensstemmels e med det europ?iske direktiv 2004/108/ec & 2006/95/ec. dutch dit product is in navolging van de bepalingen van europees directief 2004/108/ec & 2006/95/ec. eesti antud toode vastab euroopa direktiivides 2004/108/ec ja 2006/95/ec kehtestatud n?uetele. suomi t?m? tuote noudattaa eu-direktiivin 2004/108/ec & 2006/95/ec m??r?yksi?. fran?ais ce produit est conforme aux exigen ces de la directive europenne 2004/108/ec & 2006/95/ec. deutsch dieses produkt entspricht den bestimm ungen der europ?ischen richtlinie 2004/108/ec & 2006/95/ec. ??????? ? ? ??? ??????? ?? ????? ?? ?????? ????? 2004/108/ec ? 2006/95/ec. magyar e termk megfelel a 2004/108/ec s 2006/95/ec eurpai irnyelv el ? rsainak. icelandic tessi vara stenst reglugere evrps ka efnahags bandalagsins nmer 2004/108/ec & 2006/95/ec. italiano questo prodotto conforme a lla direttiva europea 2004/108/ec & 2006/95/ec. latvie?u ?is produkts atbilst eiropas direkt vu 2004/108/ec un 2006/95/ec noteikumiem. lietuvi ? ?is produktas atitinka europos direktyv ? 2004/108/ec ir 2006/95/ec nuostatas.
intel desktop board D201GLY te chnical product specification 54 malti dan il-prodott hu konformi mal-pr ovvedimenti tad-direttivi ewropej 2004/108/ec u 2006/95/ec. norsk dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004/108/ec & 2006/95/ec. polski niniejszy produkt jest zgodny z postan owieniami dyrektyw unii europejskiej 2004/108/ec i 73/23/ewg. portuguese este produto cumpre com as norm as da diretiva europia 2004/108/ec & 2006/95/ec. espa?ol este producto cumple con las norm as del directivo europeo 2004/108/ec & 2006/95/ec. slovensky tento produkt je v slade s us tanoveniami eurpskych direktv 2004/108/ec a 2006/95/ec. sloven? ? ina izdelek je skladen z dolo ? bami evropskih direktiv 2004/108/ec in 2006/95/ec. svenska denna produkt har tillverkats i enlighet med eg-direktiv 2004/108/ec & 2006/95/ec. trk?e bu rn, avrupa birli ? i?nin 2004/108/ec ve 2006/95/ec y?nergelerine uyar.
technical reference 55 2.9.3 product ecology statements the following information is provided to address worldwide product ecology concerns and regulations. 2.9.3.1 disposal considerations this product contains the following material s that may be regulated upon disposal: lead solder on the printed wiring board assembly. 2.9.3.2 recycling considerations as part of its commitment to environmental responsibility, intel has implemented the intel product recycling program to allow retail consumers of intel?s branded products to return used products to selected locations for proper recycling. please consult the http://www.intel.com/intel/other/ehs/product_ecology for the details of this program, including the scope of covered products, available locations, shipping instructions, terms and conditions, etc. ?????????? intel product recycling program ????????????????? ????? http://www.intel.com/intel/other/ehs/product_ecology deutsch als teil von intels engagement fr den um weltschutz hat das unternehmen das intel produkt-recyclingprogramm implementiert, das einzelhandelskunden von intel markenprodukten erm?glicht, gebrauchte produkte an ausgew ?hlte standorte fr ordnungsgem??es recycling zurckzugeben. details zu diesem programm, einschlie? lich der darin eingeschlossenen produkte, verfgbaren standorte, versandanweisungen , bedingungen usw., finden sie auf der http://www.intel.com/intel/other/ehs/product_ecology espa?ol como parte de su compromiso de responsabilidad medioambiental, intel ha implantado el programa de reciclaje de productos intel, que permite que los consumidores al detalle de los productos intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado. consulte la http://www.intel.com/intel/other/ehs/product_ecology para ver los detalles del programa, que incluye los productos que abarca, los lugares disponibles, instrucciones de envo, trm inos y condiciones, etc.
intel desktop board D201GLY te chnical product specification 56 fran?ais dans le cadre de son engagement pour la protection de l'environnement, intel a mis en ?uvre le programme intel product recy cling program (programme de recyclage des produits intel) pour pe rmettre aux consommateurs de produits intel de recycler les produits uss en les retour nant des adresses spcifies. visitez la page web http://www.intel.com/intel/other/ehs/product_ecology pour en savoir plus sur ce programme, savoir les produits concerns, les adresses disponibles, les instructio ns d'expdition, les cond itions gnrales, etc. ?Z ???ho??h???K? ?u???????m??u?? ??k?? u????s????? http://www.intel.com/in tel/other/ehs/product_ecology ?ZE malay sebagai sebahagian daripada komitmennya terhadap ta nggungjawab persekitaran, intel telah melaksanakan program kita r semula produk untuk membenarkan pengguna-pengguna runcit produk jenama intel memulangkan produk terguna ke lokasi-lokasi terpilih untuk dikitarkan semula dengan betul. sila rujuk http://www.intel.com/intel/other/ehs/product_ecology untuk mendapatkan butir-butir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi tersedia, arahan penghantaran, terma & syarat, dsb. portuguese como parte deste compromisso com o respei to ao ambiente, a intel implementou o programa de reciclagem de produtos para que os consumidores finais possam enviar produtos intel usados para locais selecionad os, onde esses produtos s?o reciclados de maneira adequada. consulte o site http://www.intel.com/intel/other/ehs/product_ecology (em ingls) para obter os detalhes sobre este programa , inclusive o escopo dos produtos cobertos, os locais disponveis, as instru??es de envio, os termos e condi??es, etc. russian ???? ? ?? ????? ???? ?? , intel ???? ???? ?????? ??? intel (product recycling program) ?? ???????? ???? ?????? ?? ??? intel ????? ???? ????? ??? ??????????? ?? ?? ???? ?????? . ???? , ???? ? ?? - ?? http://www.intel.com/intel/other/ehs/product_ecology ? ?????? ???? , ??????? ??? , ??? ??? , ???? ??? , ????? ??? . .
technical reference 57 trk?e intel, ?evre sorumlulu ? una ba ? ml l ? n n bir par?as olarak, perakend e tketicilerin intel markal kullan lm ? rnlerini belirlenmi ? merkezlere iade edip uygun ? ekilde geri d?n ? trmesini ama?layan intel rnleri geri d?n ? m program ?n uygulamaya koymu ? tur. bu program n rn kapsam , rn iade merkezleri, nakliye talimatlar , kay tlar ve ? artlar v.s dahil btn ayr nt lar n ?grenmek i?in ltfen http://www.intel.com/intel/other/ehs/product_ecology web sayfas na gidin. 2.9.3.3 lead free desktop board this desktop board is a european union restriction of hazardous substances (eu rohs directive 2002/95/ec) compliant product. eu rohs restricts the use of six materials. one of the six re stricted materials is lead. this desktop board is lead free although certain discrete components used on the board contain a small amount of lead whic h is necessary for component performance and/or reliability. this desktop board is referred to as ?lead-free second level interconnect.? the board substrate and the solder connections from the board to the components (second-level connections) are all lead free. china bans the same substances and has the same limits as eu rohs; however it requires different product marking and contro lled substance information. the required mark shows the environmental friendly usage period (efup). the efup is defined as the number of years for which controlled listed substances will not leak or chemically deteriorate while in the product.
intel desktop board D201GLY te chnical product specification 58 table 26 shows the various forms of the ?lead-free 2 nd level interconnect? mark as it appears on the board and accompanying collateral. table 26. lead-free board markings description mark lead-free 2 nd level interconnect: this symbol is used to identify electrical and electronic assemblies and components in which the lead (pb) concentration level in the desktop board substrate and the solder connections from the board to the components (second-level interconnect) is not greater than 0.1% by weight (1000 ppm). or or
technical reference 59 2.9.4 emc regulations desktop board D201GLY complies with the emc regulations stated in table 27 when correctly installed in a compatible host system. table 27. emc regulations regulation title fcc 47 cfr part 15, subpart b title 47 of the code of federal regu lations, part 15, subpart b, radio frequency devices. (usa) ices-003 issue 4 (class b) interference-causing equipment standard , digital apparatus. (canada) en55022: 2006 (class b) limits and methods of measurement of radio interference characteristics of information technology equi pment. (european union) en55024:1998 information technology equipment ? immunity characteristics limits and methods of measurement. (european union) en55022:2006 (class b) australian communications authority, standard for electromagnetic compatibility. (australia and new zealand) cispr 222005 +a1:2005 +a2:2006 (class b) limits and methods of measurement of radio disturbance characteristics of information technology equi pment. (international) cispr 24: 1997 +a1:2001 +a2:2002 information technology equipment ? i mmunity characteristics ? limits and methods of measurement. (international) vcci v-3/2007.04, v-4/2007.04, class b voluntary control for interference by information technology equipment. (japan)
intel desktop board D201GLY te chnical product specification 60 japanese kanji statement translation: this is a class b product based on the standard of the voluntary control council for inte rference from information technology equipment (vcci). if this is used near a radio or television receiver in a domestic environment, it may cause radio interf erence. install and use the equipment according to the instruction manual. korean class b statement translation: this is household equipment that is certified to comply with emc requirements. you may use this equipment in residential environments and other non-residential environments.
technical reference 61 2.9.5 product certification markings (board level) desktop board D201GLY has the produc t certification markings shown in table 28: table 28. product certification markings description mark ul joint us/canada recognized componen t mark. includes adjacent ul file number for intel desktop boards: e210882. fcc declaration of conformi ty logo mark for class b equipment. includes intel name and D201GLY model designation. ce mark. declaring compliance to european union (eu) emc directive and low voltage directive. australian communications authority (aca ) c-tick mark. includes adjacent intel supplier code number, n-232. japan vcci (voluntary control council for interference) mark. s. korea mic (ministry of informati on and communication) mark. includes adjacent mic certification number: cpu-D201GLY (b) for information about mic certification, go to http://support.intel.com/support/motherboards/desktop/ taiwan bsmi (bureau of standards, metrology and inspections) mark. includes adjacent intel company number, d33025. printed wiring board manufacturer?s reco gnition mark. consists of a unique ul recognized manufacturer?s logo, along with a flammability rating (solder side). v-0 china rohs/environmentally friendly use period logo: this an example of the symbol used on in tel desktop boards and associated collateral. the color of the mark may vary depending upon the application. the environmental friendly usage period (efup) for intel desktop boards has been determined to be 10 years.
intel desktop board D201GLY te chnical product specification 62
63 3 overview of bios features what this chapter contains 3.1 introduction ................................................................................... 63 3.2 bios flash memory organization .. ..................................................... 64 3.3 resource configuration ............ ........................................................ 64 3.4 system management bios (smbios)................................................. 65 3.5 legacy usb support ........................................................................ 66 3.6 bios updates ................................................................................. 66 3.7 boot options................................................................................... 67 3.8 adjusting boot speed....................................................................... 68 3.9 bios security features .................................................................... 70 3.1 introduction the board uses an intel bios that is st ored in the spi flash device and can be updated using a disk-based program. the spi flash device contains the bios setup program, post, the pci auto-configuration utility, and plug and play support. the bios displays a message during post id entifying the type of bios and a revision code. the initial production bi oss are identified as ly66210m.86a. when the bios setup configuration jumper is set to configure mode and the computer is powered-up, the bios compares the cpu version and the microcode version in the bios and reports if the two match. the bios setup program can be used to vi ew and change the bios settings for the computer. the bios setup program is acce ssed by pressing the key after the power-on self-test (post) memory test begi ns and before the operating system boot begins. the menu bar is shown below. maintenance main advanced security power boot exit note the maintenance menu is displayed only when the board is in configure mode. section 2.3 on page 44 shows how to put the board in configure mode.
intel desktop board D201GLY te chnical product specification 64 table 29 lists the bios setup program menu features. table 29. bios setup program menu bar maintenance main advanced security power boot exit clears passwords and displays processor information displays processor and memory configuration configures advanced features available through the chipset sets passwords and security features configures power management features and power supply controls selects boot options saves or discards changes to setup program options table 30 lists the function ke ys available for menu screens. table 30. bios setup program function keys bios setup program function key description < > or < > selects a different menu screen (mov es the cursor left or right) < > or < > selects an item (moves the cursor up or down) selects a field (not implemented) executes command or selects the submenu load the default configurat ion values for the current menu save the current values and exits the bios setup program exits the menu 3.2 bios flash memory organization the spi flash device includes a 4- mbit (512 kb) flash memory device. 3.3 resource configuration 3.3.1 pci autoconfiguration the bios can automatically configure pci de vices. pci devices may be onboard or add-in cards. autoconfiguration lets a user insert or remove pc i cards without having to configure the system. when a user turn s on the system after adding a pci card, the bios automatically configures interru pts, the i/o space, and other system resources. any interrupts set to available in setup are considered to be available for use by the add-in card.
overview of bios features 65 3.3.2 pci ide support if you select auto in the bios setup prog ram, the bios automatically sets up the pci ide connector with independent i/o ch annel support. the ide interface supports hard drives up to ata-66/100/133 and reco gnizes any atapi compliant devices, including cd-rom drives, tape drives, an d ultra dma drives. the interface also supports second-generation sata drives. the bios determines the capabilities of each drive and configures them to optimi ze capacity and perf ormance. to take advantage of the high capa cities typically available today, hard drives are automatically configured for logical block a ddressing (lba) and to pio mode 3 or 4, depending on the capability of the drive. you can override the auto-configuration options by specifying manual configuration in the bios setup program. to use ata-66/100/133 features the following items are required: ? an ata-66/100/133 peripheral device ? an ata-66/100/133 compatible cable ? ata-66/100/133 operating system device drivers note do not connect an ata device as a slave on the same ide cable as an atapi master device. for example, do not connect an ata hard drive as a slave to an atapi cd-rom drive. 3.4 system management bios (smbios) smbios is a desktop management interfac e (dmi) compliant method for managing computers in a managed network. the main component of smbios is the management information format (mif) database, which contains information about the computing system and its components. using smbios, a system admi nistrator can obtain the system types, capabilities, operational status, and installation dates for system components. the mif database defines the data and provides th e method for accessing this information. the bios enables applications such as third-party management software to use smbios. the bios stores and report s the following smbios information: ? bios data, such as the bios revision level ? fixed-system data, such as peripher als, serial numbers , and asset tags ? resource data, such as memory si ze, cache size, and processor speed ? dynamic data, such as event detection and error logging non-plug and play operating systems require an additional interface for obtaining the smbios information. the bios supports an smbios table interface for such operating systems. using this support, an smbios service-level application running on a non-plug and play operating system can obtain the smbios information.
intel desktop board D201GLY te chnical product specification 66 3.5 legacy usb support legacy usb support enables usb devices to be used even when the operating system?s usb drivers are not yet available. legacy usb support is used to access the bios setup program, and to install an operating system that supports usb. legacy usb support operates as follows: 1. when you apply power to the comput er, legacy support is disabled. 2. post begins. 3. legacy usb support is enabled by the bios allowing you to use a usb keyboard to enter and configure the bios setup program and the maintenance menu. 4. post completes. 5. the operating system loads. while the operating system is loading, usb keyboards and mice are recognized and ma y be used to configure the operating system. 6. after the operating system loads the usb drivers, all legacy and non-legacy usb devices are recognized by the operating system, and legacy usb support from the bios is no longer used. to install an operating sy stem that supports usb, fo llow the operating system?s installation instructions. 3.6 bios updates the bios can be updated using either of the following utilities, which are available on the intel world wide web site: ? intel ? express bios update utility, which enables automated updating while in the windows environment. using this utility, the bios can be updated from a file on a hard disk, a usb drive (a flash drive or a usb hard drive), or a cd-rom, or from the file location on the web. ? intel ? flash memory update utility, which requires booting from dos. using this utility, the bios can be updated from a file on a hard disk, a usb drive (a flash drive or a usb hard drive), or a cd-rom. both utilities verify that the updated bios matches the target system to prevent accidentally installing an incompatible bios. note review the instructions distributed with th e upgrade utility before attempting a bios update. for information about refer to bios update utilities http://support.intel.com/support/motherboards/desktop/sb/cs- 022312.htm .
overview of bios features 67 3.6.1 language support the bios setup program and help messages ar e supported in us english. additional languages are available in the intel ? integrator toolkit utility. check the intel website for details. 3.6.2 custom splash screen during post, an intel ? splash screen is displayed by de fault. this splash screen can be augmented with a custom splash screen. the intel integrator toolkit that is available from intel can be used to create a custom splash screen. note if you add a custom splash screen, it will share space with the intel branded logo. for information about refer to intel? integrator toolkit http://developer.intel.com/des ign/motherbd/software/itk/ 3.7 boot options in the bios setup program, the user can ch oose to boot from a hard drive, cd-rom, or the network. the default setting is for th e hard drive to be the first boot device, the atapi cd-rom second, and the network thir d. the fourth de vice is disabled. 3.7.1 cd-rom boot booting from cd-rom is supported in compliance to the el torito bootable cd-rom format specification. under the boot me nu in the bios setup program, atapi cd- rom is listed as a boot device. boot devices are defined in pr iority order. accordingly, if there is not a bootable cd in the cd-rom drive, the system will attempt to boot from the next defined drive. 3.7.2 network boot the network can be selected as a boot device. this selection allows booting from the onboard lan or a network add-in card with a remote boot rom installed. pressing the key during post automati cally forces booting from the lan. to use this key during post, the user access le vel in the bios setup program's security menu must be set to full. 3.7.3 booting without attached devices for use in embedded applications, the bios has been designed so that after passing the post, the operating system loader is in voked even if the following devices are not present: ? video adapter ? keyboard ? mouse
intel desktop board D201GLY te chnical product specification 68 3.7.4 changing the default boot device during post pressing the key during post causes a boot device menu to be displayed. this menu displays the list of available boot de vices (as set in the bios setup program?s boot device priority submenu). table 31 lists the boot device menu options. table 31. boot device menu options boot device menu function keys description < > or < > selects a default boot device exits the menu, saves changes, and boots from the selected device exits the menu without saving changes 3.8 adjusting boot speed these factors affect system boot speed: ? selecting and configurin g peripherals properly ? optimized bios boot parameters 3.8.1 peripheral selection and configuration the following techniques help improve system boot speed: ? choose a hard drive with parameters such as ?power-up to data ready? less than eight seconds, that minimize hard drive startup delays. ? select a cd-rom drive with a fast initialization rate. this rate can influence post execution time. ? eliminate unnecessary add-in adapter features, such as logo displays, screen repaints, or mode changes in post. th ese features may add time to the boot process. ? try different monitors. some monitors initialize and communicate with the bios more quickly, which enables the system to boot more quickly.
overview of bios features 69 3.8.2 bios boot optimizations use of the following bios setup program se ttings reduces the post execution time. ? in the boot menu, set the hard disk drive as the first boot device. as a result, the post does not first seek a diskette driv e, which saves about one second from the post execution time. ? in the peripheral configuration submenu, disable the lan device if it will not be used. this can reduce up to four seconds of option rom boot time. note it is possible to optimize the boot proce ss to the point where the system boots so quickly that the intel logo screen (or a cust om logo splash screen) will not be seen. monitors and hard disk drives with minimum initialization times can also contribute to a boot time that might be so fast that necessary logo screen s and post messages cannot be seen. this boot time may be so fast that some drives might be no t be initialized at all. if this condition should occur, it is possibl e to introduce a programmable delay ranging from three to 30 seconds (using the hard disk pre-delay feature of the advanced menu in the drive configuration subm enu of the bios setup program).
intel desktop board D201GLY te chnical product specification 70 3.9 bios security features the bios includes security features that restrict access to the bios setup program and who can boot the computer. a superv isor password and a user password can be set for the bios setup program and for booting the computer, with the following restrictions: ? the supervisor password gives unrestricte d access to view and change all the setup options in the bios setup program. this is the supervisor mode. ? the user password gives restri cted access to view and ch ange setup options in the bios setup program. this is the user mode. ? if only the supervisor password is set, pressing the key at the password prompt of the bios setup program allows the user restricted access to setup. ? if both the supervisor and user passwor ds are set, users can enter either the supervisor password or the user password to access setup. users have access to setup respective to which password is entered. ? setting the user password restricts who can boot the computer. the password prompt will be displayed before the computer is booted. if only the supervisor password is set, the computer boots with out asking for a password. if both passwords are set, the user can enter ei ther password to boot the computer. ? for enhanced security, use different pa sswords for the supervisor and user passwords. ? valid password characters are a-z, a-z, and 0-9. passwords may be up to 16 characters in length. table 32 shows the effects of setting the supervisor password and user password. this table is for reference only and is not displayed on the screen. table 32. supervisor and user password functions password set supervisor mode user mode setup options password to enter setup password during boot neither can change all options (note) can change all options (note) none none none supervisor only can change all options can change a limited number of options supervisor password supervisor none user only n/a can change all options enter password clear user password user user supervisor and user set can change all options can change a limited number of options supervisor password enter password supervisor or user supervisor or user note: if no password is set, any us er can change all setup options.
71 4 error messages what this chapter contains 4.1 bios front-panel power led codes.................................................... 71 4.2 bios error messages ....................................................................... 71 4.3 port 80h post codes ....................................................................... 72 4.1 bios front-panel power led codes the front-panel power led blinks off and on to display messages. for example, the power led is on when the system is powere d on, and blinks off for 0.5 second when processor initialization is complete. in addition, whenever a recoverable error occurs during post, the bios causes the front-pa nel power led to blink an error message describing the problem (see table 33). table 33. front-panel power led blink codes type pattern processor initialization complete on when sy stem powers up, then off for 0.5 second. post complete on when system po wers up, then off for 0.5 second. bios update in progress off when update begi ns, then on for 0.5 second, then off for 0.5 second; pattern repeats until bios update is complete. video error on-off (0.5 second each) tw o times, then 3.0 second pause (off) between on-off blink pattern; repe at entire pattern (two on-off blinks and pause) until system is powered off. memory error on-off (0.5 second each) th ree times, then 3.0 second pause (off) between on-off blink pattern; repeat entire pattern (three on-off blinks and 3-second pause) until system is powered off. thermal warning on-off (0.5 second each) fo ur times, then 3.0 second pause (off) between on-off blink pattern; repe at entire pattern (four on-off blinks and 3-second pause) until 16 th on blink, then end. 4.2 bios error messages table 34 lists the error messages and pr ovides a brief description of each. table 34. bios error messages error message explanation cmos battery low the battery may be losing power. replace the battery soon. cmos checksum bad the cmos checksum is incorrect. cmos memory may have been corrupted. run setup to reset values. memory size decreased memory size has decr eased since the last boot. if no memory was removed, then memory may be bad. no boot device available system did not find a device to boot.
intel desktop board D201GLY te chnical product specification 72 4.3 port 80h post codes during the post, the bios generates diagno stic progress codes (post codes) to i/o port 80h. if the post fails, execution stops and the last post code generated is left at port 80h. this code is useful for de termining the point wher e an error occurred. displaying the post codes requires a pci bu s add-in card, often called a post card. the post card can decode the port and disp lay the contents on a medium such as a seven-segment display. note the post card must be installed in pci bus connector 1. the following tables provide information about the post codes generated by the bios: ? table 35 lists the port 80h post code ranges ? table 36 lists the port 80h post codes themselves ? table 37 lists the port 80h post sequence note in the tables listed above, all post codes and range values are listed in hexadecimal. table 35. port 80h post code ranges range category/subsystem 00 ? 0f debug codes: can be used by any peim/driver for debug. 10 ? 1f host processors: 1f is an unrecoverable cpu error. 20 ? 2f memory/chipset: 2f is no memory detected or no useful memory detected. 30 ? 3f recovery: 3f indicated recovery failure. 40 ? 4f reserved for future use. 50 ? 5f i/o busses: pci, usb, i sa, ata, etc. 5f is an unrecov erable error. start with pci. 60 ? 6f reserved for future use (for new busses). 70 ? 7f output devices: all output co nsoles. 7f is an unrecoverable error. 80 ? 8f reserved for future us e (new output console codes). 90 ? 9f input devices: keyboard/mouse . 9f is an unrecoverable error. a0 ? af reserved for future use (new input console codes). b0 ? bf boot devices: includes fixed media and removable media. bf is an unrecoverable error. c0 ? cf reserved for future use. d0 ? df boot device selection. e0 ? ff e0 ? ee: miscellaneous codes. see table 36. ef: boot/s3 resume failure. f0 ? ff: ff processor exception.
error messages 73 table 36. port 80h post codes post code description of post operation host processor 10 power-on initialization of the host processor (boot strap processor) 11 host processor cache initialization (including aps) 12 starting application processor initialization 13 smm initialization chipset 21 initializing a chipset component memory 22 reading spd from memory dimms 23 detecting presence of memory dimms 24 programming timing parameters in the memory controller and the dimms 25 configuring memory 26 optimizing memory settings 27 initializing memory, such as ecc init 28 testing memory pci bus 50 enumerating pci busses 51 allocating resources to pci bus 52 hot plug pci controller initialization 53 ? 57 reserved for pci bus usb 58 resetting usb bus 59 reserved for usb ata/atapi 5a resetting pata bus and all devices 5b reserved for ata smbus 5c resetting smbus 5d reserved for smbus local console 70 resetting the vga controller 71 disabling the vga controller 72 enabling the vga controller remote console 78 resetting the console controller 79 disabling the console controller 7a enabling the console controller continued
intel desktop board D201GLY te chnical product specification 74 table 36. port 80h post codes (continued) post code description of post operation keyboard (ps/2 or usb) 90 resetting keyboard 91 disabling keyboard 92 detecting presence of keyboard 93 enabling keyboard 94 clearing keyboard input buffer 95 instructing keyboard controller to run self test (ps/2 only) mouse (ps/2 or usb) 98 resetting mouse 99 disabling mouse 9a detecting presence of mouse 9b enabling mouse fixed media b0 resetting fixed media b1 disabling fixed media b2 detecting presence of a fixed me dia (ide hard drive detection etc.) b3 enabling/configuring a fixed media removable media b8 resetting removable media b9 disabling removable media ba detecting presence of a removable media (ide, cd-rom detection, etc.) bc enabling/configuring a removable media bds d y trying boot selection y (y=0 to 15) pei core e0 started dispatching peims (emitted on first report of efi_sw_pc_init_begin efi_sw_pei_pc_handoff_to_next) e2 permanent memory found e1, e3 reserved for pei/peims dxe core e4 entered dxe phase e5 started dispatching drivers e6 started connecting drivers continued
error messages 75 table 36. port 80h post codes (continued) post code description of post operation dxe drivers e7 waiting for user input e8 checking password e9 entering bios setup eb calling legacy option roms ef tbd ? unrecoverable boot failure/s3 resume failure runtime phase/efi os boot f4 entering sleep state f5 exiting sleep state f8 efi boot service exitbootservices ( ) has been called f9 efi runtime service setvirtual addressmap ( ) has been called fa efi runtime service resetsystem ( ) has been called peims/recovery 30 crisis recovery has initiated per user request 31 crisis recovery has initiated by software (corrupt flash) 34 loading recovery capsule 35 handing off control to the recovery capsule 3f unable to recover
intel desktop board D201GLY te chnical product specification 76 table 37. typical port 80h post sequence post code description 21 initializing a chipset component 22 reading spd from memory dimms 23 detecting presence of memory dimms 25 configuring memory 28 testing memory 34 loading recovery capsule e4 entered dxe phase 12 starting application processor initialization 13 smm initialization 50 enumerating pci busses 51 allocating resources to pci bus 92 detecting the presence of the keyboard 90 resetting keyboard 94 clearing keyboard input buffer 95 keyboard self test eb calling video bios 58 resetting usb bus 5a resetting pata/sata bus and all devices 92 detecting the presence of the keyboard 90 resetting keyboard 94 clearing keyboard input buffer 5a resetting pata bus and all devices 28 testing memory 90 resetting keyboard 94 clearing keyboard input buffer e7 waiting for user input 01 int 19 00 ready to boot

▲Up To Search▲

Price & Availability of D201GLY

	To Download D201GLY Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .